11

Speedbar For Benelli Autoloader
Price $19.99
Greatly Increases usable area of bolt release button facilitating rapid bolt closure. Made from heat treated spring steel and matte black to match finish of weapon. Made from heat treated 4140 steel in matte black to match finish of weapon.

Oversized Safety For Benelli Autoloader
Price $26.65
Large, mushroom shaped head "TELLS" you if the safety is in the on position when finger is on the trigger. Safety can then be moved to fire position with second joint of trigger finger without moving finger from trigger. Made from heat treated 4140 steel in matte black to match finish of weapon. Can be installed for left or right hand use.

Tactical Bolt Handle For Benelli Autoloader
Price $26.65
Spool shaped handle allows rapid manipulation of bolt without "Biting". Makes operation of handle simple with either hand. Made From Heat Treated 4140 steel, matte black to match finish of weapon.

Extension Tube Nut
Price $39.99
Some models of Benelli shotguns are being shipped with no magazine extension. Instead, these models have a cap that screws onto your magazine tube. This cap holds the barrel/forend assembly firmly against the receiver. The DMW extension nut works as a coupler, allowing you to install either a factory or DMW extension tube in place of the cap. The extension tube nut holds all components firmly in place, as the factory cap does, but adds greatly to the versatility of your weapon. Made from aircraft quality aluminum, hard anodized in matte black to match the finish of your weapon.

7 Round Extension Tube
Fits M1 and M2
Length 8 1/2"
Capacity 7+1
Price $74.98
DMW Magazine tubes are made in two peices. These include the tube and the threaded collar. Great Thought and care went into these tubes to make them the strongest available. Step1 a special adhesive, rated at 300,000lbs. holding strenght, is applied to the end of the tube. Step2 the tube is pressed into the collar with an interference fit of .001"-.002". Step3 After proper cure time, the reciever end of the tube is wedged into a chamfer at the base of the collar. Step4 The unit is placed in a lathe and the threads are cut, insuring concentricity of the threads to tubes. Step5 The Muzzle end of the tube is rolled over to hold in the cap and spring. Step6 The asembly is blasted with 200 grit Alox. Step7 Assemblies are black oxide finished, cleaned, oiled, and packaged.
Note- Part number and name refer to total capacity of the magazine with a DMW tube installed. Example: BEN008 - 8 rount extension tube will give you 8 rounds in the tube + 1 in the chamber.

8 Round Extension Tube
Fits M1 and M2
Length 11"
Capacity 8+1
Price $74.98
DMW Magazine tubes are made in two peices. These include the tube and the threaded collar. Great Thought and care went into these tubes to make them the strongest available. Step1 a special adhesive, rated at 300,000lbs. holding strenght, is applied to the end of the tube. Step2 the tube is pressed into the collar with an interference fit of .001"-.002". Step3 After proper cure time, the reciever end of the tube is wedged into a chamfer at the base of the collar. Step4 The unit is placed in a lathe and the threads are cut, insuring concentricity of the threads to tubes. Step5 The Muzzle end of the tube is rolled over to hold in the cap and spring. Step6 The asembly is blasted with 200 grit Alox. Step7 Assemblies are black oxide finished, cleaned, oiled, and packaged.
Note- Part number and name refer to total capacity of the magazine with a DMW tube installed. Example: BEN008 - 8 rount extension tube will give you 8 rounds in the tube + 1 in the chamber.

9 Round Extension Tube
Fits M1 and M2
Length 13"
Capacity 9+1
Price $74.98
DMW Magazine tubes are made in two peices. These include the tube and the threaded collar. Great Thought and care went into these tubes to make them the strongest available. Step1 a special adhesive, rated at 300,000lbs. holding strenght, is applied to the end of the tube. Step2 the tube is pressed into the collar with an interference fit of .001"-.002". Step3 After proper cure time, the reciever end of the tube is wedged into a chamfer at the base of the collar. Step4 The unit is placed in a lathe and the threads are cut, insuring concentricity of the threads to tubes. Step5 The Muzzle end of the tube is rolled over to hold in the cap and spring. Step6 The asembly is blasted with 200 grit Alox. Step7 Assemblies are black oxide finished, cleaned, oiled, and packaged.
Note- Part number and name refer to total capacity of the magazine with a DMW tube installed. Example: BEN008 - 8 rount extension tube will give you 8 rounds in the tube + 1 in the chamber.

10 Round Extension Tube
Fits M1 and M2
Length 16"
Capacity 10+1
Price $74.98
DMW Magazine tubes are made in two peices. These include the tube and the threaded collar. Great Thought and care went into these tubes to make them the strongest available. Step1 a special adhesive, rated at 300,000lbs. holding strenght, is applied to the end of the tube. Step2 the tube is pressed into the collar with an interference fit of .001"-.002". Step3 After proper cure time, the reciever end of the tube is wedged into a chamfer at the base of the collar. Step4 The unit is placed in a lathe and the threads are cut, insuring concentricity of the threads to tubes. Step5 The Muzzle end of the tube is rolled over to hold in the cap and spring. Step6 The asembly is blasted with 200 grit Alox. Step7 Assemblies are black oxide finished, cleaned, oiled, and packaged.
Note- Part number and name refer to total capacity of the magazine with a DMW tube installed. Example: BEN008 - 8 rount extension tube will give you 8 rounds in the tube + 1 in the chamber.

Barrel/Extension Tube Clamp
Price $22.00
This Clamp Does not shift under recoil. Made from Aircraft grade 1018 carbon steel.